Service by manufacturer

Service for Siemens Energy SGT-100 – SGT-800 gas turbines

An independent service company whose engineers were trained at the manufacturers’ works: inspections, repairs, commissioning, combustion tuning and control system upgrades for SGT-100, SGT-200, SGT-300, SGT-400, SGT-600, SGT-700 and SGT-800 gas turbines. The team’s record includes 8 SGT-800 units at Yamal LNG and 11 in Belarus. We work in Russia, Belarus, Kazakhstan and Uzbekistan.

Models we service
  • SGT-600
  • SGT-700
  • SGT-800

The manufacturer’s names and designations are given to identify the equipment we service. The trademarks belong to their owner.

Key facts

  • Our engineers were trained at the equipment manufacturers’ works.
  • 8 SGT-800 gas turbines at Yamal LNG: supply, installation, commissioning and maintenance.
  • 11 SGT-800 gas turbine units in Belarus: installation and commissioning supervision, full load in 15 minutes.
  • Engineers on site: resident support and advice in abnormal situations.
  • Combustion tuning and engineering studies to optimise the gas turbine unit.

Models and types of work

Types of work by SGT gas turbine model: ✓ — we carry it out
ModelInspectionsRepairCommissioningCombustion tuningControl system upgrades
SGT-100✓✓✓✓✓
SGT-200✓✓✓✓✓
SGT-300✓✓✓✓✓
SGT-400✓✓✓✓✓
SGT-600✓✓✓✓✓
SGT-700✓✓✓✓✓
SGT-800✓✓✓✓✓

SGT models: small SGT-100 … SGT-400 and medium SGT-600 … SGT-800

SGT-100, SGT-200, SGT-300 and SGT-400 are small Siemens Energy machines (5–15 MW) for captive generation, cogeneration and compressor and pump drive. The generator versions of SGT-100 and SGT-300 are single-shaft, the drive versions twin-shaft; SGT-400 is a twin-shaft machine. We carry out the same types of work on these machines as on SGT-600 – SGT-800.

The SGT-600, SGT-700 and SGT-800 are Siemens Energy medium-size industrial gas turbines built at the Finspång works in Sweden. The SGT-600 and SGT-700 are twin-shaft machines with a free power turbine; the power generation and mechanical drive versions share the same engine, so these machines are used both to generate power and to drive compressors and pumps. In mechanical drive service the power turbine runs at 50–105% of its nominal speed. The SGT-800 is a single-shaft gas turbine for power generation, cogeneration and combined-cycle plants. All three models have a dry low emissions (DLE) combustion system.

SGT models: manufacturer’s data
ModelOutput, MWConfigurationMaintenance interval
SGT-1005.1 and 5.4 (power generation), 5.7 (mechanical drive)single-shaft (generation), twin-shaft (drive)—
SGT-2006.75 (power generation), up to 7.68 after upgrade——
SGT-3008.0 (power generation), 8.4 and 9.1 (mechanical drive)single-shaft (generation), twin-shaft (drive)—
SGT-40012.9 and 14.3 (power generation), 13.4 and 14.9 (mechanical drive)twin-shaft—
SGT-60024.5 (power generation), 25.2 (mechanical drive)twin-shaft34,000 EOH between hot section inspections
SGT-70032.6 and 35.2 (power generation), 33.5 and 36.2 (mechanical drive)twin-shaft, developed from the SGT-60030,000 EOH between hot section inspections
SGT-80045.3–62.5 (power generation, five ratings)single-shaftup to 60,000 EOH between major overhauls

Intervals are given in equivalent operating hours (EOH), which count starts and trips as well as the hours under load. The figures in the table measure different things: for the SGT-600 and SGT-700 the manufacturer gives the interval between hot section inspections, for the SGT-800 the interval between major overhauls, so they cannot be compared directly. According to the manufacturer, part-load operation lengthens the time between overhauls of the SGT-600 and SGT-700. On these two models the gas generator can be removed for off-site repair, while for the SGT-800 the manufacturer provides for on-site parts replacement and modular overhaul. For a specific machine the intervals come from its operating manual; what a diagnostic survey and minor inspections cover is described under Inspections and diagnostics.

Projects with this equipment

All projects

SGT-700 major overhaul: the service company and the repair plant

During a gas turbine major overhaul, hot section parts such as blades and combustor components are restored or manufactured at a specialist plant. The interaction between service and plant was the subject of a joint presentation by Energy Management LLC and Turbinaspetsservis Production Enterprise LLC (Ufa) at the 25th Russian Energy Forum in October 2025, “An integrated approach to service during the overhaul of Siemens Energy SGT-700 gas turbines”.

The presentation was based on the overhaul of two gas turbines of unit 5 at the Beryoza power plant of Brestenergo. Its conclusion: such projects cannot succeed without close cooperation between the service organisation and the plant that repairs and manufactures gas turbine parts. Following the forum, the two companies confirmed their intention to keep developing their cooperation and expand the range of Siemens Energy gas turbine parts they repair and manufacture; in March 2026 representatives of the partner worked with us on our stand at Neftegaz 2026.

Spare parts for this manufacturer

Consumables and parts for SGT gas turbines are selected against an enquiry stating the model and the serial number; for SST turbines and STC compressors the model catalogue is in the spare parts section.

Control system and digital twin

Independent service: what we rely on

Energy Management LLC is an independent service company: we do not represent Siemens Energy or act on its behalf. The team has supplied and serviced power equipment in Russia since 1996; the company itself was founded in 2022.

  • Scope of work. Maintenance and repairs are carried out on request or to the scope of the operating manual, with checks against the equipment manufacturer’s requirements.
  • Survey before work. Before installation, commissioning or maintenance we carry out a diagnostic survey: we assess the condition of the machine and its spare parts to plan the maintenance ahead and the components it will need.
  • Personnel training. We train the customer’s personnel in efficient and safe operating methods and in periodic maintenance (customer personnel training).
  • Test bench. For testing process control platforms the company has a test bench with controller, server and communications hardware and all versions of the SPPA-T3000 software available in Russia. Among other things, it is used to check updates to Kaspersky Industrial CyberSecurity for compatibility with PCS7- and SPPA-T3000-based systems.

Questions and answers

What should you do if an SGT-800 trips?

Send an urgent request with the “Equipment is down” box ticked or call +7 (495) 737-17-17. An engineer will ask for the control system event log, the nameplate data and the running hours, give first recommendations and agree the site visit.

Do you supply spare parts for SGT machines?

Consumables and parts are selected against an enquiry with the model and the serial number. We confirm the origin by catalogue numbers, markings and accompanying documents; the warranty on the parts supplied is provided by Energy Management LLC.

How often does an SGT-800 gas turbine need a major overhaul?

According to Siemens Energy, current SGT-800 ratings run up to 60,000 equivalent operating hours (EOH) between major overhauls; interim inspections follow the programme in the operating manual. EOH count not only the hours under load but also starts and trips, so machines that start often reach an overhaul sooner. For the SGT-800 the manufacturer offers maintenance concepts based on either operating hours or start cycles; which one applies to a given machine is set out in its documentation.

Can SGT hot section parts be repaired in Russia?

In many cases, yes. Blades, combustor components and casing parts of gas turbines are restored by specialist Russian plants, and missing parts are manufactured, including by reverse engineering. What can be repaired is decided after the condition assessment. How a service organisation and a plant that repairs and manufactures parts work together was the subject of our joint presentation with Turbinaspetsservis at the 2025 Russian Energy Forum, based on the overhaul of two SGT-700 units at the Beryoza power plant.

Do you service SGT-100 – SGT-400 gas turbines?

Yes: we carry out inspections, repairs, commissioning, combustion tuning and control system upgrades on SGT-100, SGT-200, SGT-300 and SGT-400 to the same scope as on SGT-600 – SGT-800. The scope for a particular machine is agreed by model and serial number.

How is a site visit organised?

After the enquiry we agree site access, the make-up of the crew and the tooling. Response and call-out times are agreed with the customer for each request and kept as short as possible.

Do you work without the original software?

Yes. We upgrade the control system and transfer the logic to SIMATIC PCS7, TIA Portal or the Russian Ezan platform, keeping the protection and governing functions.

Which inspections are due by running hours?

The scope and the intervals follow the operating manual: hot section checks, combustor and turbine inspections, medium and major overhauls. We agree the programme against the actual running hours and operating regimes.

Other manufacturers

Manufacturer names and designations are given to identify the equipment we service. Trademarks belong to their respective owners. Energy Management LLC is an independent service company.

CallSend a request
Service requestRequest a quotationData sheet