What is a gas turbine unit (GTU)

A gas turbine unit is an axial compressor, a combustor and a turbine on a common shaft together with a generator or a driven machine. The compressor compresses air, fuel is added in the combustor, the hot gases expand in the turbine and turn the shaft. It is used for power generation and for the mechanical drive of compressors and pumps.

Key facts

  • Components: axial compressor, combustor, turbine and a generator or driven machine.
  • Electrical efficiency is 32–40 % in simple cycle and 55–60 % in combined cycle.
  • Machines on this site range from 5 to 62 MW.
  • With dry low-emission combustion NOx is about 25 ppm.
  • Service follows operating hours: combustion, hot gas path and major inspections.

Components

The axial compressor compresses atmospheric air 15–20 times; the combustor (annular or can-type) burns gas or liquid fuel; the turbine expands the combustion products, gives part of the power to the compressor and the rest to the output shaft. A generator or a driven machine is coupled to the shaft directly or through a gearbox. The unit also includes the fuel system, the air intake filter house, the lube oil system, the starting device, the enclosure with ventilation and fire protection and the automatic control system.

Single-shaft and twin-shaft

In a single-shaft machine the compressor, turbine and generator are rigidly coupled and run at constant speed — 3,000 rpm for the 185 and 308 MW machines without a gearbox. In a twin-shaft machine a free power turbine is not mechanically linked to the gas generator and can change its speed to suit a compressor or pump load. Aeroderivative units — derived from aircraft engines — are usually twin-shaft.

Simple and combined cycle

In simple cycle the exhaust gases at 450–600 °C go to the atmosphere; the gross electrical efficiency of modern machines is 32–40 %. In combined cycle the exhaust heat raises steam in a heat recovery steam generator for a steam turbine, and the overall efficiency rises to 55–60 %. The intermediate option is cogeneration: the exhaust heats water or produces process steam.

Emissions and combustion tuning

Dry low-emission combustion (DLE) keeps nitrogen oxides at 25 ppm at 15 % O2 without water injection; machines with diffusion burners use water or steam injection. Combustion is tuned from actual emission and combustor dynamics measurements over the load and ambient temperature range.

Applications and range

Generation: captive power plants of industrial sites, peaking and base-load stations, distributed generation. Mechanical drive: gas compressor stations, LNG plant compressors, pumps. The site presents five machines from 42 to 308 MW with gross efficiency up to 40.1 %; the team’s references are 8 SGT-800 gas turbines at Yamal LNG and 11 in Belarus.

Maintenance

Gas turbine service follows operating hours: combustor and hot gas path inspections, major overhauls, replacement of blades and liners, vibration diagnostics, combustion tuning, control system upgrades. Resident engineers support operation at the customer’s site.

Questions and answers

How does a gas turbine differ from a gas engine genset?

A gas turbine has a larger unit size — 5 to 62 MW on this site — and a high-temperature exhaust that can raise steam. A gas engine genset wins on electrical efficiency — over 41 % — and handles part load better, but needs more frequent maintenance. A detailed comparison is in the article “Gas turbine or gas engine genset”.

How long does a gas turbine take to start?

Aeroderivative machines reach load in 5–10 minutes, which is why they serve peaking and standby plants. Heavy-duty industrial units take longer: the loading rate is limited by the warming of casings and blades. A combined-cycle plant starts even more slowly because the heat recovery steam generator and steam lines are warmed to a schedule.

How often is a gas turbine overhauled?

Work is planned by equivalent operating hours including the number of starts: a borescope inspection usually yearly, a combustion inspection at 8–12 thousand hours, hot gas path at 24–33 thousand and a major inspection at 48–66 thousand. The exact intervals are set by the manufacturer, and diagnostics by vibration and emissions allow dates to be shifted by condition. See inspections and diagnostics.

Related terms

Updated: 2026-09-23

CallSend a request